donkeyday4
donkeyday4
0 active listings
Last online 4 weeks ago
Registered for 4+ weeks
Send message All seller items (0) easycuci.art
About seller
Not all my methods have been so profitable. In 2022 I measured a couple different methods at 19 watts and 27 watts as a part of Curbing the “Gas-Guzzling” tendencies of AMD Radeon with Multi-Monitor . While I did handle to get that 27 watt AMD system down in energy some time later, not every CPU/motherboard combo is destined for the ten watt ballpark. Before going additional, the 7 watt figure for this system was earlier than storage has been added. Be aware that if I don’t allow powertop to disable the keyboard, I get eight watts measured at the wall.Let’s get into detailed specs and component choices. DDR4 and reuse a CPU I already have. Sometimes you just must take your greatest educated guesses by way of components, build your rig, tune what you'll be able to, and let the chips fall the place they may. Earlier than I start, right here is a quick look at the motherboard format. The Inexperienced CPU-connected slots and ORANGE chipset-connected slots will turn into related throughout this write-up. One in all my objectives above was the capacity for an eventual 6 NVMe drives. Digging into deeper details as to why this generally is a challenge (feel free to skip this section)… Downside: There are zero client motherboards with 6x M.2 slots that can all be used at the identical time in PCIe mode.’ll discover that when you attempt to populate all 6, the last one must be a SATA variant. The ASRock Z790 PG Sonic also has 6 slots, but you'll be able to solely use 5 of them (with a legitimate excuse: they provide a Gen5 NVMe slot but it surely comes with an either/or caveat). Why This Downside Exists: There are chipset lane limitations on consumer boards. Assuming I want the flexibility to run all M.2 in Gen4x4 and assuming a manufacturer had been actually prepared to commit all the lanes to M.2 NVMe slots (they’re not), AMD X570 and Intel B760 would max at three M.2 slots, with AMD B650 and Intel H670/Q670/Z690/W680 managing 4.5 M.2 slots is possible on AMD X670 and Intel H770 boards. Six on a Z790 board. Beyond that, extraordinary measures like robbing the principle PCIE slot of lanes can be required. The solution: PCI-E to M.2 adapters turned obligatory. Now when searching for a motherboard, it grew to become a matter if adding the M.2 slots included to any available PCI-E slots capable of x4 or larger. My options have been now limited to AMD X570, Intel H770, and Intel Z790 motherboards.Word that whereas utilizing bifurcation is a risk on some motherboards to get greater than 1 NVMe out of the primary PCIe slot, I determined not to rely on it. 7w). AMD chipset power consumption has concerned me for some time, as earlier X570 chipsets had a TDP of 11w and wanted a fan. Chipset Speed: Intel H670/Q670/W680/Z690/H770/Z790 chipsets have a DMI 4.0 x8 hyperlink to the CPU. AMD X570/B650/X670 have a PCIe 4.0 x4 link to the CPU.1. I already had 64GB of DDR4 that the Intel system could use. AMD 600-sequence chipsets are all DDR5-solely. 2. I already had an Intel 12th Gen CPU. 3. I’ve but to see any positive discussion around AM5 power consumption. In any respect. Update: as I was scripting this, news actually got here out about AMD 7000-sequence CPUs burning/bulging the place the motherboard socket pins meet the CPU. Yeah, sorry AMD, not this time.So Intel it was. After checking out available DDR4 motherboards available on the market, I quickly narrowed choices to 2 manufacturers: MSI and ASUS. Don’t care in regards to the board comparisons? Be at liberty to skip this. The enticing MSI boards had been the Pro Z790-P WIFI DDR4 and Z790-A WIFI DDR4. Nearly an identical on the surface, except the “A” is somewhat more premium (audio, rear ports, heatsinks, energy phases, and so on). Con: My current B660 board that ends in larger idle consumption than expected is an MSI. Attractive ASUS options had been the Prime H770-Plus D4 and Prime Z790-P D4 (optionally available WIFI edition). Stepping into the TUF, Strix, or ProArt was just too expensive. The Z790-P D4 is similar besides it has more energy phases, better heatsinking, more USB ports, extra fan header, and for our purposes…Ultimately the ASUS Prime H770-Plus D4 was about $100 cheaper at the time and is what I selected. One upside I’ve found with “cheaper” boards is they are likely to have fewer parts and thus less vampire energy drain at idle, although this isn’t at all times a certainty. I already had this CPU as part of a previous desktop construct. I used to be getting a brand new motherboard with 2xDP anyway, and going older-gen didn’t make sense to me.That desktop construct turned out to be a disappointment, and ranks as one among my least favorite builds. I had issues where generally only 1 of two DP-hooked up displays would wake in Linux which meant I needed to both pull/reconnect the opposite DP connector, or manually suspend/resume the system so it might strive again. Another subject was that rebooting between Home windows/Linux sometimes brought on odd issues which necessitated a full poweroff/restart. Hardware decode on Ubuntu utilizing Wayland is still problematic and when programs tried to use it to play video, issues would ensue. Lastly, in contrast to my previous Intel systems which may all be introduced down close to the 10 watt mark, this one was idling at 19 watts, though I suspected the MSI motherboard I was using may have been an element.Many of the headaches I experienced were associated to the GPU and show. Since I was about to construct something server-oriented, that was not a factor. This was memory I already had. I ran the four sticks of memory at the XMP profile of the dual-rank kit which was 16-18-18-36. All the things else was primarily left to the defaults except that I ran the RAM at 1.25 volts (greater than inventory 1.20, however decrease than the XMP 1.35v setting).This component wasn’t deliberately chosen. Once i needed a recent Ubuntu Server install for testing, this occurred to be the one SSD I had kicking round that wasn’t currently being used. I was going to be doing loads of A/B testing on PCIE and NVMe gadgets, so putting in Ubuntu 23.04 to a SATA SSD made sense to keep PCIE slots free. Be aware that after testing, the main OS was to be run on a Samsung SSD 970 EVO Plus 500GB NVMe. Not much to say except that Samsung stuff tends to reliably go into low power modes. Having used both drives, I can’t measure any power difference between them in my testing.Tom’s Hardware tested the Samsung idle at 0.072 watts (via ASPM/APST), and Anandtech tested the Sandisk Ultra 3D idle to be 0.056 watts (via ALPM). Both are effectively below the 1W resolution of my Kill-A-Watt meter. As much as this 750W PSU could look like overkill for a system meant to sit around 10 watts, when 12 drive motors spin up at the identical time, the instantaneous load is more likely to be fairly high.Seagate states 2A/3A DC/AC peak currents on the 12V rail for one among their 10TB 3.5″ drives. This bursty energy demand has the potential to be problematic if the PSU isn’t up to the task. If an array of 6 drives collectively pull 150-200 watts at the same second the CPU spikes to drag a peak 120W, that’s a leap from around 10 watts idle to around four hundred watts. This could simply cause an instantaneous voltage dip - if it dips enough to trigger an instantaneous crash/reboot it’s most likely not an enormous deal, but when it dips simply sufficient that knowledge is corrupted throughout a memory refresh or when another drive is mid-write…’s a extra painful problem. Oversizing the PSU to some degree (or including some in-line capacitors to the facility rails) makes sense. Happily, regardless of working exterior of the peak effectivity range, a lot of the Corsair RM collection is fairly environment friendly across a variety. 9-10 watts was the consumption when the show output was on. 600 kernel boot parameter for a 600s timer), which is the place this system sits many of the week. Eight watts was the consumption if the USB keyboard energy management was disabled. In case you don’t SSH into the server from elsewhere, spending the additional watt for keyboard use could be essential.As talked about to start with, I began with 12 arduous drives. Half have been 2.5″ and the opposite half have been 3.5″. As a result of the motherboard solely has four SATA ports, a SATA controller and a port multiplier were used to handle the remaining drives. Moreover, 4 NVMe drives have been used early on: one in all them, a Western Digital SN770 had a tendency to get fairly hot even at idle which indicates it probably wasn’t going into a low energy mode.With all of the equipment connected, at idle, with display off, and with the 12 drives spun right down to standby, I was shocked to see that my idle power consumption had gone from 7 watts all the way up to a whopping 24-25 watts. Far too much! One thing was amiss. I disconnected the hard drives and began testing components one at a time. These had been pretty crude tests meant to get a rough idea as to the culprit, so numbers right here aren’t exact. I shortly found that the JMB585 SATA controller I was utilizing caused energy consumption to increase by something within the 6-10 watt range (precise measurements in a later section).The controller itself is just alleged to take a couple watts, and the tiny heatsink stayed cool, so there was obviously extra happening. The place was the power going? I decided to look at the CPU package C-states. With out the JMB585 SATA controller, the system hit C6. When the JMB585 was reconnected, the most effective the system hit was C3. Ah ha! But why? Seems that if a PCIE-linked gadget won’t go into ASPM L1, the CPU won’t go into as deep a sleep.The JMB585 controller cards don’t seem to have ASPM help. A bit of additional experimentation revealed one thing else that I hadn’t identified, and it has to do with C6 vs C8. The system will only hit C8 if there’s nothing hooked up to the CPU-connected PCIE lanes. In different phrases, if something is plugged in to the highest PCIE slot or the top NVMe slot, C6 is the maximum. So while C8 could be a luxurious, hitting C6 was a should.C3 makes use of an excessive amount of energy. If SATA controllers had been going to stop the CPU from hitting the very best energy saving states, I started to wonder whether or not I ought to have been looking for a motherboard with 6-8 SATA ports in order that I wouldn’t have to depend on add-on controllers… A bit looking for SATA HBAs confirmed that whereas there aren’t many options right here, the ASM1166 SATA controller should support ASPM L1, though the firmware needs to be flashed for it to work properly (and to work at all on newer Intel boards).This was something I’d must order: I have Marvel and JMicron spares, but they don’t support ASPM. I’d actually been avoiding ASMedia for years, but out of necessity they were now getting one other probability: I ordered a pair ASM1166 6 port SATA controllers. Value a mention… During initial testing with a WD Black SN770 (Gen4 NVMe), I found an issue when the first (prime CPU-attached) PCIE and NVMe ports had been used. ’t stop the errors, however decreased them considerably. Some analysis showed the foundation trigger could be any number of things. As a result of swapping the motherboard or CPU wasn’t a nice thought, my best hope was swapping to a distinct brand of NVMe.I ordered some Crucial P3 NVMe drives. This turned out to be a successful endeavor: with the WD drives changed by the Essential drives, I used to be not getting any errors, though keep in mind these are Gen3 drives. When i had the 2 Crucial P3 NVMe drives put in within the CPU-linked PCIEx16 slot and the top M2 slot, I noticed increased idle temps than anticipated. Whereas the NAND sat at about 27-29C, the controllers were reporting 49-50C - a lot larger than I expected for these specific drives. I moved the one from the PCIEx16 slot to a chipset-related PCIEx4 slot. L1 sub-states solely appear to get enabled on the chipset-linked slots.Unlucky, but it surely does appear to coincide with the obtainable BIOS settings in the screenshot above. I put each NVMe drives on chipset-connected PCIE slots. Unfortunately when making an attempt numerous A/B tests using these 2 Essential NVMe drives with completely different slot configurations and various BIOS settings, I noticed very inconsistent habits when it comes to temperature, though it’s price noting the JMB585 and an NVMe boot drive have been additionally connected throughout these tests. For instance, both drives would possibly idle at round 40C till a comfortable reboot at which point 1 (or each) might now idle at the 50C range. Generally it seemed possible to maintain 1 drive on the CPU-linked M.2 and retain 40C temperatures on both drives as long as the x16 slot wasn’t populated.Presumably I was hitting some form of bug. The Samsung boot NVMe appeared to keep a constant idle temperature regardless of what was taking place with the Crucial NVMe drives, so I suspected the Crucial drives themselves are at the very least partly to blame. Interestingly, generally one (or both) controller temps would drop all the way in which right down to the 29C range when on the chipset-related slots. Late Replace: I sadly didn’t keep monitor of temperatures all through the remainder of the testing, and heatsinks/airflow between drives have all been jumbled round. Power Consumption Puzzles - Swapping from the JMB585 to the ASM1166.After a couple weeks the ASM1166 arrived. First a pair bits concerning the card which you may discover helpful if you’re considering it… I began with a firmware flash - ASM1166 playing cards typically have previous firmware which doesn’t work with Intel 600-sequence motherboards and from what I perceive can have issues with power management. For anyone planning to purchase one of these ASMedia cards, I should word that like most SATA controllers and HBAs on the market, the standard actually varies. Certainly one of my cards had a heatsink that was on a bit crooked: the thermal pad was thick sufficient to stop it from shorting close by parts, however remember that these merchandise can be actually hit-and-miss.This is among the situations the place paying somewhat extra to buy from someplace with a very good return coverage can be prudent. I did quite a little bit of A/B testing, so right here is a fast “JMicron JMB585 vs ASMedia ASM1166” when it comes to complete system power consumption, though it might solely be applicable to this platform (or maybe even this particular motherboard). First, energy consumption with none drives related to the playing cards (the SATA SSD boot drive is linked to the motherboard) to get a baseline. 1 watt). Measurements after the display output went to sleep. 14 watts) the place the CPU package deal power state plummets to C2.Shockingly, the JMB585 behaves in an reverse method where it’s consumption is decrease on the CPU-linked slot (and it didn’t trigger C2) - nonetheless, you’ll soon see that issues change when drives are literally related… I did additional testing with the controllers, together with enjoying “musical chairs” with a pair NVMe drives to see if multiple devices would throw a wrench into things, but nothing unexpected occurred so I’ll skip these details. With baseline measurements complete, subsequent it was time to actually put some drives on these controllers. The SATA SSD boot drive stayed on the motherboard, 2 NVMe drives had been added to the combination (chipset-linked except otherwise noted), and four of the 2.5″ SATA hard drives were placed on the controller.I’ll record the “spun down” consumption after the laborious drives went into standby - “spun up” was exactly 2 watts greater in each check whereas the drives had been idle. 8 watts. No contest. An extra benefit is that I used to be able to make use of each of the ASM1166 playing cards within the system, whereas attempting to use both of my JMB575 cards at the same time resulted within the system refusing in addition, though that may very well be a platform or motherboard-particular concern.There's a commerce-off though - I at all times found the JMB585 to be rock-solid dependable, together with when paired with a JMB575 port multiplier. My past experience with ASMedia SATA controllers has been less than stellar: reliability with the ASM1166 stays to be seen, however on the very least it’s a bad candidate for a port multiplier because it doesn’t assist FBS (only CBS). 1. When removing/reinserting the NVMe boot drive, a BIOS message appeared claiming that it couldn’t boot because of GPT corruption. The ASM1166 cards had to be briefly removed for the BIOS to “find” the NVMe boot drive once more (after which they may very well be reinstalled).Linux has to iterate by all of them. One of many comments mentioned an older Samsung 840 Professional SSD limiting to C3 whereas an important Pressure GT SSD allowed C8. While these are older drives, I nonetheless found this a bit stunning. It was value investigating. I used the H770 as a testbed with a Samsung 850 EVO SATA SSD boot drive together with a crucial P3 NVMe and built a custom kernel to permit the Realtek community adapter to reach L1.2. No ASM1166, just using the Intel onboard SATA.I reached C10 after working powertop with auto-tune and allowing the display to sleep. I tried varied drives I've readily available, powering off the system each time to swap drives and repeat the process. Right here were the outcomes. I suggest being cautious when selecting SATA SSD manufacturers and models. I’ll try to update this checklist over time with drives I’ve tested, however keep in mind sure manufacturers in the storage area have shown a propensity towards silently swapping to inferior components in a few of of their mainline merchandise, so it's best to at all times confirm the claimed performance metrics of any storage devices you purchase whereas inside your return window.Be happy to go away a comment with good/dangerous drives you come across. 1) Motherboard support and BIOS configuration are vital - I’ve had motherboards with very inflexible BIOS’s. On this one, “Native ASPM” and the appropriate L1 states must be enabled (to allow OS-controlled as a substitute of BIOS-controlled) for low power consumption to work. 2) Gadgets all have to help ASPM L1. In any other case you’re actually rolling the dice. The toughest part here as you might need guessed is finding SATA controllers that support it - if potential, get a motherboard sufficient sufficient Intel chipset-connected SATA ports to avoid needing a separate card.I should be aware that finding NVMe drives which have working low-energy APST power states underneath ASPM isn’t at all times a given and you’ll want to do a little analysis there too. 3) If you may hit the C8 power state, keep away from utilizing CPU-attached PCIe lanes (high PCIe and M2 slot). On this particular motherboard, my advice would be to avoiding utilizing them altogether if you may, until you either need the low-latency full-bandwidth path to the CPU or your devices are so energetic they never sleep anyway.Recall that Each my JMicron and ASMedia SATA playing cards prompted the CPU Bundle C-State to plummet to C2 if plugged into the x16 PCI-E slot. 14USD delivery on the time through eBay). At the moment I discovered our rarely-used fax machine which was at all times powered on used 7 watts… 10 years greater than paid for the Kill-A-Watt. Seagate charges standby consumption of those 3.5″ drives at about 0.8w each, and the 2.5″ drives at about 0.18w each. This traces up with what I’m seeing above.My lively-idle numbers really match up pretty properly to Seagate specs too. The apparent statement: in comparison with the rest of the system parts, the 3.5″ drives are power-hungry monsters. The HDDs will eventually be changed with SSDs. With idle consumption as little as it is throughout HDD standby, there isn’t a major rush and this process will progressively take place as my HDD drives/spares fail and SSD prices fall. The plan for “end game” is for an all-SSD construct.Originally the plan was for 1 boot drive, 6xNVMe (seemingly Crucial P3 4TB) for a RAIDZ2 array, and 6xSATA (seemingly Samsung 870 QVO 8TB) for the 2nd RAIDZ2 array. Since using the CPU-connected M2/PCIe slots not solely brings unpredictability but also comes at a slight C-state/power/temperature cost, I might alter that plan and quit a pair NVMe in the first array and use SATA instead in order that I don’t need to touch CPU-related lanes. This half is just price studying if you’re enthusiastic about meticulous particulars in regards to the storage.Be at liberty to skip to the ultimate part otherwise. As alluded to earlier, this is a Samsung 970 EVO Plus. At the moment lower than 4GB of the 500GB space is used (a 64GB swap partition exists however all the time sits at 0 used). It was initially chosen as a result of Samsung had developed a reputation for reliability (which has been falling by the wayside these days), and Samsung also scored effectively in evaluations each time it got here to idle power consumption. This drive is nearly at all times idle and both Controller and NAND temps stayed low all through all testing (20-24C). It might ultimately be swapped to a SATA SSD to free up an NVMe port.These drives are used for the primary 6-drive ZFS RAIDZ2 array - the one that gets essentially the most use. Someday per week it’s busy with a activity that includes reading a couple of TB over the course of 24 hours. Utilization through the remainder of the week is sporadic, and the drives spend a lot of the week spun down. EASYCUCI official registration link of the 2.5″ Seagate drives is actually fairly spectacular. Spun down they’re each rated at 0.18w, in low energy idle they’re rated at 0.85w, and the learn/write averages are rated at about 2w. There are plenty of SSDs out there with worse energy consumption numbers than this spinning rust.5TB capacity gives a lot of storage-per-watt. Not great performers. 80-120MB/s peak read/write. To be truthful though, many TLC/QLC SSDs fall to these write ranges when their SLC cache is exhausted. SMR (Shingled Magnetic recording). Reads are wonderful, but write performance absolutely plummets when random writes happen - it acts like a QLC SSD without an SLC cache that additionally doesn’t have TRIM. Low rated workload (55TB/year vs 550TB/12 months for 3.5″ Exos drives). No configurable error restoration time (SCT ERC), and these drives can dangle for minutes if they hit an error whereas they relentlessly try to re-read the problematic sector. Ubuntu needs to be configured to wait as a substitute of making an attempt to reset the drive after 30 seconds.Larger error charges if they heat up (I’ve had to substitute a couple of and have found they don’t like working sizzling). Typical HDD pain points (sluggish to spin up, and many others). To be completely truthful to Seagate, these are bought as external USB backup drives. Pulling these 15mm tall drives out of the enclosures and utilizing them as RAID members in a NAS isn’t precisely utilizing them as meant. The extremely low power consumption is great, but there are obvious trade-offs. Long run, these 2.5″ 4/5TB drives will slowly be changed by 4TB SSD drives (probably all NVMe).SSDs in 4TB capability began to change into accessible on the patron end in 2021/2022 at about 4-5x the price of the spinners. Less than 2 years later they’ve dropped to about 2x the fee, and that i expect decent manufacturers to final more than 2x as long because the Seagate spinners. If availability of the Essential P3 (Gen3) model remains, I’ll probably keep with this model regardless of being limited to Gen3 speeds.I strongly thought of the Essential P3 Plus (Gen4), but energy consumption in opinions was greater despite only a few situations where efficiency was notably increased as well. My biggest concern with the P3 Plus (Gen4) was that if I had issues with ASPM/APST, Tom’s Hardware showed it with a 0.3w idle energy premium over the P3 (Gen3) for the 2TB mannequin. I want “worst-case scenario” power to be as low as possible. Used in the secondary 6-drive RAIDZ2 array - a backup array that’s spun up for about 2 hours every week the place it receives constant heavy writes.Energy consumption of the 3.5″ Seagate drives is about what you’d anticipate. These 10TB drives are rated at about 0.8w every in standby, 2-5w idle, and 6-9w studying and writing. These are rated to collectively pull about 45-50 watts when writing. That’s a bit of extra UPS load I don’t actually need if a lengthy power outage takes place through the backups (I follow client 1500 watt UPS’s). These are rated to collectively pull about 4.8 watts when in standby. Again, some UPS load I wouldn’t thoughts shaving off. Lengthy-time period these drives will doubtless be replaced by Samsung 870 QVO 8TB SATA drives. The 870 QVO sports 0.041w/0.046w idle with ALPM, 0.224w/0.229w idle with out, and 2.0-2.7w throughout a duplicate (based on Toms/Anandtech).Value-wise, the Samsung 8TB SATA SSD is presently a good bit costlier than 8TB spinners (nearer to 3x the cost) so until these drives start to see more frequent use for some motive, substitute with the SSDs will almost certainly wait until I’ve run out of spares. Changing my spinning rust with SSDs is a process that can likely take some time. “Special” Allocation Class - lets you create a vdev particularly for metadata and for “small” blocks if desired. A cache drive, identified generally as an L2ARC.Should you create the “special” vdev at pool creation, all your metadata (and optionally, small blocks of a measurement you select) will go on the “special” vdev as an alternative of your spinning rust. Very quick file listings and listing traversal while keeping the spinning rust for the files themselves. Sure, you may “ls” a bunch of directories with out waking your HDDs from sleep. Largest draw back is that as a result of all your metadata is on this vdev, if it ever dies, access to all your information is actually gone. So it actually must be not less than mirrored.Possibly even a 3-approach mirror. Say goodbye to some ports. The L2ARC is a bit completely different. It’s essentially a level 2 cache. When the cache in RAM gets full, ZFS will copy a few of the blocks to the L2ARC before it evicts that content from RAM. The next time that information needs to be accessed, it’ll be read from the L2ARC as a substitute of the disk. One benefit compared to the “special” vdev is that you’re high-quality with only 1 SSD - if there’s an issue with the info in the L2ARC (bad checksum, drive dies, and so forth), ZFS will simply learn the content from the original disk.Also, once the L2ARC is full, ZFS will simply start once more at the beginning of the L2ARC SSD and overwrite stuff it wrote before which has some professionals (previous information by no means accessed anymore) and cons (knowledge that was frequently accessed and might want to get written to the L2ARC again). You can even add/remove L2ARC gadgets from the pool at your leisure - need so as to add a 64GB SSD, 500GB SSD, and 2TB SSD? Go proper ahead - ZFS will distribute blocks among them.Need to remove the 500GB SSD from the pool just a few days later and use it elsewhere? Go proper ahead. The largest downside to the L2ARC is that if you happen to forget to specify “cache” when including the machine, you most likely mucked up your pool. It’s additionally imperfect: even with cautious tuning it’s exhausting to get ZFS to jot down Every part you need to the L2ARC earlier than it will get evicted from memory. At the identical time, depending in your information, the L2ARC might see a variety of writes, and you may have to fastidiously watch the well being of your SSD. Previously I’ve used the “special”, used L2ARC, and have used both at the same time (you may even inform the L2ARC to not cache things already contained within the “special” vdev).NVMe drives to stay in low power mode more…). Conclusion - Regrets? Second-guessing? What may have gone in another way? Not like the ASRock J4005 build where I realized half manner by way of that I’d kneecapped myself in a number of ways, I don’t get the identical sense here. This time I ended up with low idle energy AND a fairly succesful system that must be flexible even if repurposed sooner or later. I’m quite pleased with my element selections, though I’d be curious to know how the MSI Pro Z790-P DDR4 (considered one of the other motherboards I thought of) would do as compared. Performance-clever the MSI has the advantage of 6xSATA ports, but it surely comes with the apparent draw back of the notorious Intel 2.5G networking chip.The MSI additionally has a PS/2 port and I’ve never actually checked to see if PS/2 keyboard energy consumption is decrease than USB (recall that I save 1 watt if I permit powertop to shut down the USB keyboard port). And naturally it can be attention-grabbing to check the ASPM and ALPM settings, and to see if the snags I hit with CPU-attached PCIe/M.2 slots exist in the same means. Whereas this system currently sits in the 15-sixteen watt range when idle with drives in standby, as soon as all HDDs are changed with SSDs, I’d count on idle consumption of round 10-11 watts which isn’t bad for 72TB value of drives, 64GB of RAM, and a fairly first rate processor.Replace: Current Linux kernels disable the L1 power saving modes of most Realtek NICs which prevents the CPU from getting into first rate C-states, thus increasing power consumption by rather a lot. While there are workarounds, shifting ahead I’ll probably limit myself to motherboards containing Intel 1 Gigabit network adapters (maybe transferring to Intel 2.5 Gigabit when it becomes clear they’ve labored out all of the kinks). Yow will discover additional details about the Realtek NIC state of affairs in the comments below. The script I mention deep in the comments may be found at: RTL8125-ASPM.sh.txt .

donkeyday4's listings

User has no active listings
Are you a professional seller? Create an account
Non-logged user
Hello wave
Welcome! Sign in or register